English
Industry News
You are here: Home » News » News » Industry News
2026
DATE
07 - 29
TNC Connector: Types, Frequency Range, Applications, and Selection Tips
TNC Connector: Types, Frequency Range, Applications, and Selection Tips
You might see the TNC Connector when you need a strong and safe connection for wireless networks or tools. This connector has threads, so it works better than BNC connectors, especially when the frequency is high. You can use it with coaxial cables that need 50 or 75-ohm impedance. The usual frequen
Read More
2026
DATE
07 - 24
X-Band Microwave Pulse Power Amplifier Guide for Radar and RF Test Systems
X-Band Microwave Pulse Power Amplifier Guide for Radar and RF Test Systems
X-Band Microwave Pulse Power Amplifier Guide for Radar and RF Test SystemsAn X-band microwave pulse power amplifier increases the power of pulsed RF signals operating within the X-band frequency range, generally defined as 8 to 12 GHz. These amplifiers are used in radar transmitters, electronic warf
Read More
2026
DATE
07 - 21
Microwave Power Amplifier Guide: Key Specifications, Applications, and Selection Tips
Microwave Power Amplifier Guide: Key Specifications, Applications, and Selection Tips
A microwave power amplifier increases the power of an RF or microwave signal so that it can drive an antenna, device under test, transmission line, or downstream RF subsystem at the required level. It is commonly used in radar, satellite communications, electronic warfare, EMC immunity testing, wire
Read More
2026
DATE
04 - 28
RF Connector Torque Guide: Correct Tightening Torque for SMA, N, 3.5 mm, 2.92 mm, and 4.3-10
RF Connector Torque Guide: Correct Tightening Torque for SMA, N, 3.5 mm, 2.92 mm, and 4.3-10
You need the right torque for every rf connector to protect your equipment and keep rf signals strong. For SMA and N connectors, use 10 to 13 inch-pounds. This table helps you see the standard values for each connector:Connector TypeTorque Value (inch-pounds)SMA10 to 13N10 to 133.5 mmN/A2.92 mmN/A4.
Read More
2026
DATE
04 - 21
Phase Stable Cable vs Phase Matched Cable: Key Differences, Applications, and Selection Tips
Phase Stable Cable vs Phase Matched Cable: Key Differences, Applications, and Selection Tips
You should understand the difference between phase stable cable and phase matched cable. This helps your system work the way you want. Phase stable cable keeps the phase steady even when things change. Phase matched cable makes sure signals arrive at the same time in many cables. Picking the right c
Read More
2026
DATE
04 - 14
50 Ohm vs 75 Ohm RF Connectors
50 Ohm vs 75 Ohm RF Connectors
You might ask what makes 50 Ohm and 75 Ohm rf connectors different. The biggest difference is how they deal with signal loss and power. People use 50 Ohm connectors in business because they do better with high frequencies. Most home electronics use 75 Ohm connectors since they lose less signal over
Read More
2026
DATE
03 - 26
Can SMA Mate with 2.92 mm or 3.5 mm Connectors? Compatibility, Risks, and Best Practices
Can SMA Mate with 2.92 mm or 3.5 mm Connectors? Compatibility, Risks, and Best Practices
You can connect an SMA connector to a 2.92 mm or 3.5 mm connector, but there are risks. In high-frequency rf uses, the signal can get worse if you use a high-quality male connector with a low-quality female connector. If you use a low-quality male connector, you might break important parts. The qual
Read More
2026
DATE
03 - 23
4.3-10 vs 7/16 DIN: Which Low-PIM Connector Should You Use for Modern Base Stations?
4.3-10 vs 7/16 DIN: Which Low-PIM Connector Should You Use for Modern Base Stations?
If you want the best low-PIM performance in new base stations, you should pick the 4.3-10 RF connector. This connector gives better electrical performance and lower PIM. It helps keep your signal strong and steady. Low-PIM is important because it stops unwanted interference. Interference can make ne
Read More
2026
DATE
03 - 23
RF Connector types: SMA vs N-Type vs BNC vs TNC and which is right for your application
RF Connector types: SMA vs N-Type vs BNC vs TNC and which is right for your application
You need to choose the right RF connector for your project. SMA connectors are good for high-frequency jobs like WiFi, GPS, and radio astronomy. N-Type connectors are best for outdoor and high-power systems. They work well with antennas and base stations. BNC connectors are used for quick-connect jo
Read More
2025
DATE
12 - 21
A 28-nm CMOS Breakthrough for 6G: Compact 90–180 GHz Power Amplifier Achieves Octave Bandwidth And High Output Power
A 28-nm CMOS Breakthrough for 6G: Compact 90–180 GHz Power Amplifier Achieves Octave Bandwidth And High Output Power
As 6G communications accelerate toward the terahertz regime (above 100 GHz), the 90–180 GHz spectrum has emerged as a key frequency range for enabling ultra-high-speed data transmission beyond 100 Gbps and high-precision terahertz sensing. However, power amplifiers operating in this band have long f
Read More
  • Total 9 pages  Go to Page
  • Go
Our company, Zhejiang LenoRF Industry co. LTD, occupies an area of 30 hectares and is equipped with world class equipment to make millimeter wave connectors and phase stable cables. We specialize in coaxial connectors, cable assembly, and passive devices. Our current products are the latest millimeter wave connector and phase stable cable on the market.

Quick Links

Products

Contact Us

 +86-13052906618
    +86-0511-88896168
 No2.Xindingmao Industrial Zone, Zhenjiang,Jiangsu, China
Leave a Message
Inquiry Now
Copyright©2023 LenoRF Industry Co.,Ltd.      Sitemap